Dev48
Language
  • About
  • Services
  • Industries
  • Technologies
  • Articles
  • Contacts
Book a call
    Home/Articles/Measure wood shapes to increase yield rate from log profiles to finished thickne
Dev48
info@dev48.org+375 29 320-40-96WhatsApp@isky_by

© 2026 · All rights reserved.

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness

Source: Keyence•November 20, 2026 at 06:31 AM

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness

This section explains wood scanning in the lumber processing stage by dividing it into two processes: log profiling for lumber breakdown optimization (green mill) and finishing/engineered wood thickness and warp management (planer mill). We introduce configurations that stably capture shapes…

Three Reasons Why Wood Shape Measurement Determines Yield Rate and Quality

Because the ratio of material costs is high, measurement directly leads to profit.

Sawing Cannot Be Optimized Without Knowing the Shape of the Log

Logs differ from one to another in diameter, curvature, and taper. If logs are sawed into standard shapes without understanding their geometry, products that should have been obtained cannot be produced, increasing waste. By continuously acquiring cross-sectional profiles, the most valuable sawing pattern can be determined for each log. In processes with a high ratio of material costs, a change in yield rate of just a few percent directly impacts profitability.

Variations in Finished Thickness Lead to Defects in Subsequent Processes

In planer finishing and engineered wood manufacturing, variations in thickness lead to bonding and assembly defects. For products with multiple layers of laminas, such as glulam and CLT (cross-laminated timber), variations in a single sheet accumulate and cause the overall dimensions to fall out of specification. Since sample inspection cannot capture variations along the entire length, a system is required to measure the thickness of all products along their entire length while they are running.

Knots, Color Variation, and Rough Surfaces Make Inspection Using Gray-Scale Images Difficult

The color of wood varies greatly due to knots and vessels, and there are also variations in the shading of the wood grain. In inspections that judge based on color or brightness, the shading of the wood grain may be misidentified as a defect, or conversely, depressions may be overlooked. By capturing height as a physical quantity, it is less affected by color variation, allowing for the evaluation of shape defects such as depressions and cracks. Defects that are distinguished by color, such as knots, are inspected using gray-scale images that can be acquired simultaneously with height images.

Four Measurement Points on a Lumber Processing Line

The purpose of measurement changes between the sawing process (lumber) and the finishing process (planer).

  • 1 Acquiring log profiles – Process ①. Continuously acquire the cross-sectional shape of logs to understand diameter, curvature, and taper. This serves as the starting point for yield rate optimization as a basis for sawing decisions.
  • 2 Understanding knots/defects and grading – Process ②. Shape defects such as depressions and cracks are captured with height data, and knots are captured with gray-scale images that can be acquired simultaneously. This makes it difficult to misidentify color variations in wood grain or vessels as defects.
  • 3 Measuring finished shapes – Process ③. Measure the cross-sectional shape of tongues and grooves after processing using 3D data to quantify steps, widths, and angles. Because it is captured with height data, it is less affected by color variations in the wood.
  • 4 Full-length thickness management – Process ④. Measure the thickness along the entire length based on the roller. Variations in the width direction can also be understood, leading to the management of laminated products such as glulam and CLT.

Comparison of Methods for Measuring Wood Shape and Thickness

Differences in methods appear under conditions such as color variation, rough surfaces, and total length measurement.

① Log profile (diameter/curvature)

Laser triangulation method (LJ-X8000 Series)

◎ Continuous acquisition of cross-sectional shapes

2D vision sensor (Gray-scale/planar inspection)

△ Profile only

Contact roller gauge

× Cannot measure

Sample inspection + calipers

△ Limited to a few points

② Knot/defect detection

Laser triangulation method (LJ-X8000 Series)

◎ Shape defects are detected by height, and knots are detected by gray-scale images

2D vision sensor (Gray-scale/planar inspection)

△ Wood grain is easily misidentified as defects

Contact roller gauge

× Cannot detect

Sample inspection + calipers

× Cannot detect

③ Finished shape (tongue and groove)

Laser triangulation method (LJ-X8000 Series)

◎ Calculates step, width, and angle from the cross-section

2D vision sensor (Gray-scale/planar inspection)

△ Planar dimensions only

Contact roller gauge

△ Limited measurement points

Sample inspection + calipers

△ Limited to a few points

④ Full-length thickness management

Laser triangulation method (LJ-X8000 Series)

◎ Measures thickness across the full length and width using the roller as a reference

2D vision sensor (Gray-scale/planar inspection)

× Cannot measure thickness

Contact roller gauge

○ Can measure full length, but leaves contact marks

Sample inspection + calipers

× Total length cannot be measured

⑤ Warpage/waviness

Laser triangulation method (LJ-X8000 Series)

◎ Evaluated as surface height distribution

2D vision sensor (Gray-scale/planar inspection)

× Cannot be evaluated

Contact roller gauge

△ Becomes a set of points

Sample inspection + calipers

× Cannot be evaluated

Resistance to color variation and rough surfaces

Laser triangulation method (LJ-X8000 Series)

◎ Height data is less susceptible to color variation

2D vision sensor (Gray-scale/planar inspection)

× Strongly affected

Contact roller gauge

◎ Not affected

Sample inspection + calipers

◎ Not affected

Measurement during conveyance

Laser triangulation method (LJ-X8000 Series)

◎ Corrects misalignment, tilt, and vibration

2D vision sensor (Gray-scale/planar inspection)

△ Requires setup

Contact roller gauge

○ Possible

Sample inspection + calipers

× Stopping is required

Recording of measured values

Laser triangulation method (LJ-X8000 Series)

◎ Saves and outputs measured values and images

2D vision sensor (Gray-scale/planar inspection)

○ Images can be saved

Contact roller gauge

○ Output is possible

Sample inspection + calipers

× Relies on manual recording

Reasons to Choose the LJ-X8000 Series for Wood Measurement

Wood is a difficult target to inspect using gray-scale images because it has both color variation and a rough surface. Because the LJ-X8000 Series detects shape defects using height data, it is not easily affected by the color of the wood grain, and knots can be inspected using gray-scale images acquired at the same time. Since the cross-section is acquired as is, everything from log profiles to post-finishing steps, grooves, and thicknesses can be handled using the same principle. The 3D position correction function corrects for misalignment and tilt during transport, and the profile alignment function corrects for the effects of vibration, preventing inspection points from shifting.

Products Compatible With Scanning in Wood and Lumber Processes

This measurement system quantifies the cross-sectional shape as is, even for wood with color variation or rough surfaces.

Compatible With Log Profiling and Finished Thickness Control — LJ-X8000 Series

2D/3D Laser Profiler

Ultra-high-definition measurement of 3200 points/profile represents the cross-sectional shape in detail, quantifying indicators such as height, step, width, and angle. Height images generated from height data are not easily affected by color variation caused by wood grain, knots, or vessels, making it difficult to mistake color changes for defects. For knot inspection, gray-scale images acquired simultaneously with height images can be used. The 3D position correction function corrects for target misalignment and tilt, and the profile alignment function corrects for the effects of vibration during transport, allowing inspection points to track automatically. It is not easily affected by changes in distance or height differences, enabling clear imaging even for targets whose diameter changes significantly, such as logs. Inspections can be set up simply by choosing from a wide variety of measurement tools that measure steps, widths, cross-sectional areas, angles, and more, and it also supports inspection of long targets during transport. It also supports NG notification via judgment output and saving of measured values and images using the FTP server function.

View Catalog

Click here for product information on the LJ-X8000 Series

Get Detailed Materials on the LJ-X8000 Series

You can download a free catalog summarizing sensor head specifications, measurement tools, and system configurations.

View Catalog

Inquiries about scanning in wood and lumber processes

Examples of Use in Wood and Wood-Based Building Materials

It is used for everything from grading to shape measurement after processing and full-length thickness control.

Wood Grading and Knot Inspection

The size and shape of wood are measured and used for grading. Because judgment is based on shape, it is not easily affected by the wood grain, allowing for inspection of dents, and knots are inspected using gray-scale images acquired at the same time.

Measurement of Tongue and Groove Shape After Processing

A line laser is applied to the side of flooring material immediately after processing to measure the width and step from the cross-sectional shape of the tongue and groove. Because the 3D data averages out the roughness of the wood surface, stable measurement and inspection are possible even if there is roughness.

3D Inspection of Finished Material Surfaces

The surface of the board during transport is captured using height data to detect shape defects such as dents and cracks, which are then used for grading. It is not easily affected by the shading of the wood grain color, and knots can be inspected using gray-scale images acquired at the same time.

Frequently Asked Questions About Wood and Lumber Scanning

Because judgment is based on the physical quantity of height, shape defects can be evaluated without being easily affected by color changes due to wood grain or vessels. Defects that are distinguished by color, such as knots, are inspected using gray-scale images acquired at the same time.

Yes, it is stable. Since height images are not easily affected by surface colors or patterns, the shape can be captured even on rough wood. We will propose settings and sensor heads according to the surface conditions.

Yes, they can be measured. Because it is less susceptible to distance changes and height differences, clear images can be captured even for targets with varying diameters. We will propose the sensor head models, quantity, and layout based on the required measurement range and the area you want to capture.

The purpose of the sawing process is to obtain log profiles (as a basis for lumber breakdown decisions), while the finishing process aims for full-length management of the finished shape and thickness. Since the targets to be measured and the required fields of view differ, we design the configuration for each process.

Yes, it can be measured. A configuration based on rollers supports inline full-length measurement, allowing you to understand thickness variations in the width direction as well. This is effective for managing glulam and CLT laminas.

Yes, they will align. The 3D position correction function corrects for target misalignment and tilt, and the profile alignment function corrects for the effects of vibration during conveyance, allowing the inspection points to follow automatically.

  • 2D/3D Laser Profiler LJ-X8000 series

2D/3D Laser Profiler

LJ-X8000 series

← All articles

What this article says

More in Industrial & Industry 4.0

All →
How NVIDIA Ros and Universal Robots accelerate robotics innovation
Universal Robots

How NVIDIA Ros and Universal Robots accelerate robotics innovation

A Comprehensive Guide to ICS Protection | Rockwell Automation | US
Rockwell Automation

A Comprehensive Guide to ICS Protection | Rockwell Automation | US

Rockwell Automation Signs Definitive Agreement to Acquire AGILOX | Rockwell Automation | US
Rockwell Automation

Rockwell Automation Signs Definitive Agreement to Acquire AGILOX | Rockwell Automation | US

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment
Keyence

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds
Keyence

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface
Keyence

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface

More from Keyence

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment
Keyence

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds
Keyence

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds

Numerically Managing Probe and Socket Wear: Determining Replacement Timing by Dimensions, Not Appearance
Keyence

Numerically Managing Probe and Socket Wear: Determining Replacement Timing by Dimensions, Not Appearance

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface
Keyence

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface

3D Burr Measurement on Parts: Non-Contact, 100% Inline Quantitative Inspection
Keyence

3D Burr Measurement on Parts: Non-Contact, 100% Inline Quantitative Inspection

Non-Contact Inline Inner Diameter Measurement: 100% Inspection of Through-Holes and Rings
Keyence

Non-Contact Inline Inner Diameter Measurement: 100% Inspection of Through-Holes and Rings