Dev48
Language
  • About
  • Services
  • Industries
  • Technologies
  • Articles
  • Contacts
Book a call
    Home/Articles/Continuously measuring cross sections immediately after extrusion measuring wall
Dev48
info@dev48.org+375 29 320-40-96WhatsApp@isky_by

© 2026 · All rights reserved.

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment

Source: Keyence•November 20, 2026 at 06:32 AM

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment

This section explains a configuration that continuously monitors cross-sectional profiles (wall thickness, width, and corner radius) under high-temperature and vibration conditions immediately after extrusion, and feeds back to die adjustment. While touching on the respective difficulties of…

Three Reasons to Measure Immediately After Extrusion

In a continuous process, the later you notice a defect, the longer the defective section becomes.

Defective Sections Cannot Be Identified Through Sample Inspection

Extrusion is a non-stop process. Even if the cross-section changes due to die clogging or fluctuations in temperature and extrusion pressure, with an operation that measures by sampling after cutting, it is impossible to know when the deviation started. As a result, you have to trace back to the previous inspection and suspect the entire batch. If the cross-section is continuously measured immediately after extrusion, only the sections that deviate from the specifications can be isolated, minimizing waste and rework.

Cross-Sections Cannot Be Managed Without Simultaneously Checking Thickness, Width, and Corner R

The quality of extruded products is not determined by a single dimension. Areas with insufficient thickness lose strength, if the width deviates, it will not fit during assembly, and if the corner R changes, it affects appearance and sealing performance. Moreover, these change simultaneously from the same die state. Instead of measuring a few points with calipers, it is necessary to acquire the entire cross-sectional shape and evaluate multiple items simultaneously.

Immediately After Extrusion, High Temperatures, Vibration, and Material Difficulties Are Compounded

Immediately after leaving the die, the temperature is high, and contact will deform the target. The conveyor line vibrates, causing the target to shake up and down. Difficulties specific to each material are also compounded. Rubber is black and returns almost no light, resin is translucent and light penetrates inside, and aluminum has a glossy surface with strong reflections. In addition to being non-contact, continuous monitoring is not possible unless the method can handle these three conditions.

4 Steps in the Extrusion Line

In addition to measuring and judging, the process is built as a series of steps up to providing feedback to die adjustment.

  • 1 Acquire the cross-section immediately after extrusion – Process 1. The cross-sectional shape immediately after leaving the die is acquired using a line laser. Since it is non-contact, it can measure the target even in high-temperature and flexible states.
  • 2 Elimination of vibration and waviness – Process 2. The profile alignment function removes the effects of conveyance vibration and workpiece waviness. Even with shaking targets, the shape itself can be evaluated.
  • 3 Calculation of thickness, width, and corner R – Process 3. From the acquired cross-section, thickness, width, corner R, angle, and cross-sectional area are calculated simultaneously using measurement tools. Multiple control items can be evaluated together in a single measurement.
  • 4 Feedback to die adjustment – Process 4. Out-of-specification conditions are notified by judgment output, and measured values are returned upstream in real time. This can be used for die adjustment and correction of extrusion conditions.

Comparison of Cross-Section Measurement Methods for Extruded Products

Differences in methods appear from three perspectives: control items such as thickness and corner R; conditions immediately after extrusion such as high temperature, vibration, and material difficulty; and feedback to die adjustment.

(1) Thickness

LJ-X8000 Series (Light section method)

○ Calculated at areas where both front and back sides are visible

Optical dimension measurement system (thrubeam method)

× Only the outer shape can be detected

Contact gauge

△ Limited measurement points

Image dimension measurement system (after cutting/sample inspection)

○ Can be measured if the cross section is cut

(2) Width/Outer shape

LJ-X8000 Series (Light section method)

◎ Simultaneously calculated from the cross section

Optical dimension measurement system (thrubeam method)

◎ High-speed continuous measurement

Contact gauge

△ Limited measurement points

Image dimension measurement system (after cutting/sample inspection)

○ Can be measured, but offline

(3) Corner R/Angle

LJ-X8000 Series (Light section method)

◎ Evaluated from the cross-sectional shape

Optical dimension measurement system (thrubeam method)

× Cannot be evaluated

Contact gauge

× Cannot be evaluated

Image dimension measurement system (after cutting/sample inspection)

○ Can be measured, but offline

(4) Compatibility with irregular cross sections

LJ-X8000 Series (Light section method)

◎ Directly acquires the cross section

Optical dimension measurement system (thrubeam method)

△ Only visible as the light-blocked width

Contact gauge

△ Jig required depending on the shape

Image dimension measurement system (after cutting/sample inspection)

◎ Can accommodate irregular cross sections

High-temperature targets

LJ-X8000 Series (Light section method)

◎ Non-contact (including applications with a water-cooled jacket)

Optical dimension measurement system (thrubeam method)

◎ Non-contact

Contact gauge

× Cannot measure

Image dimension measurement system (after cutting/sample inspection)

× Only after cooling

Conveyance vibration and undulation

LJ-X8000 Series (Light section method)

◎ Eliminated with profile alignment function

Optical dimension measurement system (thrubeam method)

○ Corrected using tilt correction

Contact gauge

△ Affected

Image dimension measurement system (after cutting/sample inspection)

Black rubber/translucent resin

LJ-X8000 Series (Light section method)

◎ Supported by single-shot HDR/translucent object function

Optical dimension measurement system (thrubeam method)

○ Captured by the light-shielding position

Contact gauge

○ Not affected

Image dimension measurement system (after cutting/sample inspection)

△ Condition setup is required

Feedback to die adjustment

LJ-X8000 Series (Light section method)

◎ Measurement values can be returned in real time

Optical dimension measurement system (thrubeam method)

◎ Can be returned (outer dimensions only)

Contact gauge

× Practically impossible

Image dimension measurement system (after cutting/sample inspection)

× Performed after the fact

Why the LJ-X8000 Series Is Chosen for Cross-Section Management Immediately After Extrusion

While thrubeam-type micrometers can measure outer dimensions, thickness and corner R cannot be evaluated without cross-sectional shape data. Because the LJ-X8000 Series digitizes the cross-section as is, thickness, width, corner R, angle, and cross-sectional area can be managed together. The single-shot HDR function and translucent object function support everything from black rubber to translucent resin, and the profile alignment function eliminates conveying vibration.

Products Compatible With Extrusion Profile Measurement

This measurement system acquires the cross-section immediately after extrusion as is, and simultaneously digitizes the thickness, width, and corner R.

Compatible With Rubber, Resin, and Aluminum Extrusions — LJ-X8000 Series

2D/3D Laser Profiler

With ultra-high-definition measurement of 3,200 points/profile, the cross-sectional shape is represented in detail, and indicators such as thickness, width, step, angle, cross-sectional area, and corner R are digitized simultaneously. Since the cross-section can be acquired simply by projecting a line laser, even non-circular, irregularly shaped cross-sections can be evaluated as they are. For areas where both the front and back surfaces are visible, thickness can also be measured by installing sensor heads above and below. With the single-shot HDR function, even if light-absorbing black rubber and highly reflective metal coexist in the same field of view, both can be captured in a single image. The translucent object function works for translucent resins where laser light penetrates inside, and the stray light suppression function works for multiple reflections and diffuse reflections from glossy surfaces after extrusion, enabling accurate shape measurement. The profile alignment function eliminates the effects of vibration during conveying and workpiece waviness, allowing the shape itself to be evaluated. Positioning is also unnecessary thanks to the 3D position correction function. Inspection can be set up simply by choosing from a variety of measurement tools such as step, width, cross-sectional area, and angle. It also supports judgment output, real-time feedback to upstream processes, and saving of measurement values and images using the FTP server function.

View Catalog

Click here for LJ-X8000 Series product information

Get Detailed Materials on the LJ-X8000 Series

You can download a free catalog summarizing sensor head specifications, measurement tools, and system configuration.

View Catalog

Inquiries regarding inline measurement of extruded profiles

Examples of Extrusion Measurement Applications

Used for everything from rubber extrusion molded products to resin extrusions and cable jackets.

Weatherstrip Shape Measurement

Enables continuous management and feedback control of extrusion molded products that are soft and difficult to measure with contact methods. This can also be applied to cross-section management of rubber extrusions.

Dimension and Chipping Inspection of Extruded Resin

Performs various dimension measurements and appearance inspections after extrusion. Using the surface shape data of the target, width and height measurements and chipping inspections can be performed simultaneously.

Cable Unevenness Inspection

Inspects unevenness on the jacket surface from the cross-sectional shape. Even with continuous objects like extruded jackets, shape abnormalities can be captured while they are moving.

Frequently Asked Questions About Inline Measurement of Extrusion Profiles

Image dimension measurement systems are well suited for sample dimension inspection. What is covered on this page is continuous monitoring immediately after extrusion, with the purpose of “quickly finding sections that deviate from specifications and feeding back to die adjustment.” The two have different roles.

If the front and back surfaces are visible, sensor heads can be installed above and below to calculate the thickness from the cross-sectional shape. The inner surface of a closed hollow part cannot be measured because it cannot be seen from the outside. Since the configuration varies depending on the shape of the target and the surfaces that can be measured, we will propose a configuration after you show us a cross-sectional drawing.

Because it is a non-contact method, it does not touch the target. In high-temperature environments, there are installation examples using water-cooled jackets. We will propose a configuration after asking about the installation location and ambient temperature.

In many cases, they can be captured. The single-shot HDR function works for black rubber with low reflection, and the translucent object function works for translucent resin where light penetrates inside, representing accurate shapes. Since conditions vary depending on the material and color, we will propose a configuration after asking about the target.

The profile alignment function removes the effects of vibration and waviness during conveyance, allowing the shape itself to be evaluated. The 3D position correction function also eliminates the need for positioning.

Yes, they can. In addition to NG notification via judgment output, real-time feedback to upstream processes is supported. Measured values can be saved using the FTP server function and can also be used for trend management.

  • 2D/3D Laser Profiler LJ-X8000 series

2D/3D Laser Profiler

LJ-X8000 series

← All articles

What this article says

More in Industrial & Industry 4.0

All →
How NVIDIA Ros and Universal Robots accelerate robotics innovation
Universal Robots

How NVIDIA Ros and Universal Robots accelerate robotics innovation

A Comprehensive Guide to ICS Protection | Rockwell Automation | US
Rockwell Automation

A Comprehensive Guide to ICS Protection | Rockwell Automation | US

Rockwell Automation Signs Definitive Agreement to Acquire AGILOX | Rockwell Automation | US
Rockwell Automation

Rockwell Automation Signs Definitive Agreement to Acquire AGILOX | Rockwell Automation | US

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds
Keyence

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness
Keyence

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface
Keyence

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface

More from Keyence

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds
Keyence

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness
Keyence

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness

Numerically Managing Probe and Socket Wear: Determining Replacement Timing by Dimensions, Not Appearance
Keyence

Numerically Managing Probe and Socket Wear: Determining Replacement Timing by Dimensions, Not Appearance

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface
Keyence

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface

3D Burr Measurement on Parts: Non-Contact, 100% Inline Quantitative Inspection
Keyence

3D Burr Measurement on Parts: Non-Contact, 100% Inline Quantitative Inspection

Non-Contact Inline Inner Diameter Measurement: 100% Inspection of Through-Holes and Rings
Keyence

Non-Contact Inline Inner Diameter Measurement: 100% Inspection of Through-Holes and Rings