Dev48
Language
  • About
  • Services
  • Industries
  • Technologies
  • Articles
  • Contacts
Book a call
    Home/Articles/Judging exterior deformation by depth managing swelling wrinkles dents and depre
Dev48
info@dev48.org+375 29 320-40-96WhatsApp@isky_by

© 2026 · All rights reserved.

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds

Source: Keyence•November 20, 2026 at 06:31 AM

Judging Exterior Deformation by Depth: Managing Swelling, Wrinkles, Dents, and Depressions With Thresholds

This section explains how to detect cell-type-specific deformations, such as swelling and wrinkles in pouch cells and side dents in prismatic cans, using height data. It goes as far as how to create pass/fail thresholds, such as what micrometer depth of a dent should be classified as NG, and…

Three Reasons Why Exterior Deformation Inspection Is Unstable

As long as humans judge “whether there is deformation,” the standards will continue to fluctuate.

Deformation Appears Differently Depending on the Cell Type

Since pouch cells use aluminum laminated film, swelling due to internal gas generation and wrinkles during transport and sealing are issues. For prismatic cans, dents on the sides and corners are the main issues, and impact marks caused by transport jigs or handling also appear as similar depressions. Even for the same “exterior deformation,” the measurement method changes depending on whether you look at swelling as a surface or local depressions. If you try to judge under a single condition without separating the cell types, one of them will be missed.

Visual Inspection Standards Depend on the Individual

Visual or image-based appearance inspection results vary depending on lighting conditions and inspector experience. Especially for cell exteriors, there are printed characters, logos, and film gloss, making it difficult to distinguish between deformation and patterns using only contrast. If standards shift from line to line or shift to shift, it is impossible to explain “what was considered acceptable” when a defect occurs later. A system that judges based on physical quantities is required.

Cannot Judge Without a Threshold

Unless you define “from how many micrometers of dent or impact mark a part is considered defective,” you cannot make a judgment even if you can measure it. Thresholds must be determined by calculating backward from assembly interference in subsequent processes or internal effects. By first measuring the distribution of deformation in acceptable lots to understand the current status, and then setting the threshold at a level that differentiates them from defective parts, both over-detection and missed defects can be suppressed.

4 Steps to Determine Thresholds and Perform 100% Inspection

In addition to implementing a measurement system, the process must be designed up to the creation of judgment standards.

  • 1 Determine the measurement surface for each cell type – STEP 1. First, determine the measurement surface and evaluation index for each cell type, such as swelling and wrinkles across the entire surface for pouches, and dents and impact marks on the sides and corners for prismatic cans.
  • 2 Obtain deformation amount with height data – STEP 2. Obtain height as a 3D image. Since it is not affected by background text or logos, it is less likely to mistake exterior printing for deformation.
  • 3 Determine thresholds – STEP 3. Measure the distribution of deformation in acceptable lots to understand the current status, and set the threshold at a level that differentiates them from defective parts. The balance between over-detection and missed defects can be adjusted numerically.
  • 4 100% judgment and recording – STEP 4. Reject defective parts based on judgment output, and save NG images and measured values. By keeping these along with the history of threshold changes, the judgment standards can be explained.

Comparison of Exterior Deformation Detection Methods

The key differences lie in whether the deformation amount can be recorded numerically and whether the system is unaffected by printing or gloss.

(1) Pouch cell swelling (surface rise)

LJ-X8000 Series (3D cross-section profile)

◎ Quantified as surface height distribution

2D image sensor (2D inspection using grayscale only)

× Cannot determine height

Visual inspection

△ Only large ones

Contact gauge

△ Limited to a few points

② Pouch cell wrinkles

LJ-X8000 Series (3D cross-section profile)

◎ Extracted as local height differences

2D image sensor (2D inspection using grayscale only)

△ Unstable if there is no contrast

Visual inspection

△ Depends on the viewing angle

Contact gauge

× Cannot detect

③ Dents and impact marks on the side of rectangular cans

LJ-X8000 Series (3D cross-section profile)

◎ Determine depth numerically

2D image sensor (2D inspection using grayscale only)

× Cannot determine depth

Visual inspection

△ Judgment depends on the individual

Contact gauge

△ Measurement points are limited

④ Dents and scratches on corners

LJ-X8000 Series (3D cross-section profile)

◎ Detect scratches and deformation separately

2D image sensor (2D inspection using grayscale only)

○ Scratches are easy to detect

Visual inspection

△ Defects are easily overlooked

Contact gauge

× Cannot detect

⑤ OK/NG threshold setting

LJ-X8000 Series (3D cross-section profile)

◎ Set/change with numerical values in µm

2D image sensor (2D inspection using grayscale only)

△ Uses indirect indicators such as area

Visual inspection

× Standards are verbal

Contact gauge

△ Only values at a few points

Resistance to printing, logos, and gloss

LJ-X8000 Series (3D cross-section profile)

◎ Not easily affected because it uses height data

2D image sensor (2D inspection using grayscale only)

× Patterns are easily misdetected as defects

Visual inspection

△ Appearance changes

Contact gauge

○ Unaffected

Inline 100% inspection

LJ-X8000 Series (3D cross-section profile)

◎ Supports 100% inspection without positioning

2D image sensor (2D inspection using grayscale only)

○ 100% inspection is possible

Visual inspection

× 100% inspection is not realistic

Contact gauge

× Tact time cannot be met

Recording judgment basis

LJ-X8000 Series (3D cross-section profile)

◎ Saves deformation amount and NG images

2D image sensor (2D inspection using grayscale only)

○ Images can be saved

Visual inspection

× Difficult to keep records

Contact gauge

× Relies on manual recording

Reasons to Choose the LJ-X8000 Series for Exterior Deformation Detection

Because the LJ-X8000 Series acquires deformation as a physical quantity of height, thresholds such as “how many µm of depression is considered NG” can be set directly. Dents caused by transport or handling can also be handled using the same depth index. Because height images are not affected by printing or logos on the exterior, or the gloss of the film, patterns are not mistaken for defects. Combined inspection of grayscale and 3D images also allows scratches and deformation to be handled separately.

Products Compatible With Battery Exterior Deformation Detection

This inline profiler quantifies deformation as height, allowing 100% inspection with thresholds in µm units.

Compatible With Deformation Detection of Pouches and Prismatic Cans — LJ-X8000 Series

2D/3D Laser Profiler

Ultra-high-definition measurement of 3200 points/profile represents surface shapes in detail, quantifying the amount of deformation as a physical quantity of height. Both overall surface swelling and local depressions such as dents and impact marks can be handled as depth from the same height data. By extracting irregularities from free-form surfaces, only local depressions can be extracted even for targets with slightly curved surfaces.

Because height images generated from height data are not affected by printing or logos on the exterior, or the gloss of the film, patterns are less likely to be mistaken for defects. Because it supports combined inspection that combines grayscale and 3D images, surface scratches and shape deformation can be handled separately. It is less susceptible to changes in distance or height differences, allowing stable imaging even if cell dimensions change due to product changeovers. The 3D position correction function automatically corrects for target misalignment and tilt, eliminating the need for positioning. When combined with the automatic target detection function, inline 100% measurement and inspection can be achieved. It also supports rejecting NG products via judgment output and saving NG images and measured values using the FTP server function, allowing operations that keep judgment criteria and their evidence.

View Catalog

Click here for product information on the LJ-X8000 Series

Get Detailed Materials on the LJ-X8000 Series

You can download a free catalog summarizing sensor head specifications, measurement tools, and system configuration.

View Catalog

Inquiries regarding battery exterior deformation and impact mark inspection

Examples of Cell Exterior Inspection Applications

It is used for appearance inspection of various batteries, such as prismatic, pouch, and cylindrical types, to detect dents and scratches.

Cell Appearance Inspection (Prismatic)

Performs appearance inspection of individual cells. Dents occurring on corners and scratches on sides are stably inspected using not only grayscale images but also 3D images.

Cell Appearance Inspection (Pouch)

Performs appearance inspection of pouch-type batteries. Because 3D data is image-processed, even gentle dents that are difficult to detect with 2D image processing can be stably inspected.

Exterior Can Appearance Inspection (Cylindrical)

Performs appearance inspection of the side of cylindrical batteries. Even for gentle dents that conventional cameras struggle with, the LJ-X8000 Series detects them using height data, enabling stable inspection.

Frequently Asked Questions Regarding Detection of Battery Exterior Swelling, Wrinkles, Dents, and Impact Marks (LJ-X8000 Series)

After calculating the required level based on assembly interference in subsequent processes and internal impacts, the distribution of deformation in acceptable lots is measured to understand the current status. Setting a threshold at a level that differentiates them from defective products can suppress both over-detection and missed detections.

Yes, it does. For pouch cells, the focus is on swelling (bulging) across the entire surface and localized wrinkles, while for prismatic cans, it is mainly on dents and impact marks on the sides and corners. For cylindrical cells, gentle dents on the sides are the main focus. It is important to determine the measurement surface and evaluation indicators in advance for each cell type.

No, they are not. Because judgment is based on height data, the system does not react to color information such as printed text, logos, or patterns. Even slight unevenness within the same color can be stably inspected using height information.

Yes, they can. By extracting unevenness from free-form surfaces, gentle curves of the surface are treated as the reference, allowing only localized dents on top of them to be evaluated.

Although both can be handled using height data, the evaluation indicators are different. Dents are viewed as the depth of localized depressions, while swelling is viewed as the amount of bulging across the entire surface, so the measurement surfaces and thresholds are set separately. You can operate by switching inspection settings while keeping the same sensor configuration.

Yes, it can. The system supports saving images of NG products and measured value data, which can be stored long-term using the FTP server function. By saving these along with the threshold settings, you can maintain a state where the judgment criteria can be explained.

  • 2D/3D Laser Profiler LJ-X8000 series

2D/3D Laser Profiler

LJ-X8000 series

← All articles

What this article says

More in Industrial & Industry 4.0

All →
How NVIDIA Ros and Universal Robots accelerate robotics innovation
Universal Robots

How NVIDIA Ros and Universal Robots accelerate robotics innovation

A Comprehensive Guide to ICS Protection | Rockwell Automation | US
Rockwell Automation

A Comprehensive Guide to ICS Protection | Rockwell Automation | US

Rockwell Automation Signs Definitive Agreement to Acquire AGILOX | Rockwell Automation | US
Rockwell Automation

Rockwell Automation Signs Definitive Agreement to Acquire AGILOX | Rockwell Automation | US

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment
Keyence

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness
Keyence

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface
Keyence

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface

More from Keyence

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment
Keyence

Continuously Measuring Cross-Sections Immediately After Extrusion: Measuring Wall Thickness, Width, and Corner Radius, and Feeding Back to Die Adjustment

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness
Keyence

Measure Wood Shapes to Increase Yield Rate: From Log Profiles to Finished Thickness

Numerically Managing Probe and Socket Wear: Determining Replacement Timing by Dimensions, Not Appearance
Keyence

Numerically Managing Probe and Socket Wear: Determining Replacement Timing by Dimensions, Not Appearance

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface
Keyence

Measure and Track Guide Rail Wear Numerically: Capture Degradation Through the Cross-Sectional Shape of the Raceway Surface

3D Burr Measurement on Parts: Non-Contact, 100% Inline Quantitative Inspection
Keyence

3D Burr Measurement on Parts: Non-Contact, 100% Inline Quantitative Inspection

Non-Contact Inline Inner Diameter Measurement: 100% Inspection of Through-Holes and Rings
Keyence

Non-Contact Inline Inner Diameter Measurement: 100% Inspection of Through-Holes and Rings