Dev48
Language
  • About
  • Services
  • Industries
  • Technologies
  • Articles
  • Contacts
Book a call
    Home/Articles/Surface finish symbols and chart how to read and specify surface finish on a dra
Dev48
info@dev48.org+375 29 320-40-96WhatsApp@isky_by

© 2026 · All rights reserved.

Surface Finish Symbols and Chart: How to Read and Specify Surface Finish on a Drawing

Source: Keyence•November 16, 2026 at 09:47 AM

Surface Finish Symbols and Chart: How to Read and Specify Surface Finish on a Drawing

Learn how to read surface finish symbols, use a surface finish chart of Ra values and N-grades, and specify and verify finish on a drawing.

A surface finish specification on a drawing tells a machinist what texture a surface must have, how it is produced, and how it will be checked. It is written as a symbol, a roughness parameter such as Ra, a limit value in micrometers (µm) or microinches (µin), and sometimes a lay direction. This guide explains how to read surface finish symbols, how to use a surface finish chart of Ra values and N-grades, and how to verify the callout on the finished part.

Key Takeaways

  • A surface finish callout combines a symbol, a roughness parameter, a limit value, and, when they matter, a production method and lay direction.
  • There are three basic surface finish symbols: any process allowed, material removal required, and material removal prohibited.
  • ISO roughness grades N1 to N12 map to fixed Ra values. For example, N8 equals Ra 3.2 µm (125 µin) and N6 equals Ra 0.8 µm (32 µin).
  • 1 µm equals about 39.4 µin. Older US drawings often use µin and the term RMS, which is about 1.11 times Ra on a sinusoidal profile.
  • Appearance finishes such as bead blasted, brushed, and anodized are usually specified by process or reference sample, not by Ra alone.
  • Surface finish measurement should use the same parameter, cutoff, and trace direction the drawing calls for.

What Does a Surface Finish Specification Include?

A surface finish specification is more than a single number. Each element answers a different question for the person making or inspecting the part, and leaving one out is a common source of disputes between a supplier and a customer.

Symbol

What it states

Whether machining is required or prohibited

Example

Basic symbol with a bar

Parameter

What it states

Which roughness measure applies

Example

Ra or Rz

Limit value

What it states

The maximum allowed roughness, or a range

Example

1.6 µm (63 µin)

Production method

What it states

How the surface is made, if it matters

Example

Ground

Lay

What it states

The direction of the dominant pattern

Example

⊥ (perpendicular)

Cutoff / sampling length

What it states

The filter used when measuring

Example

0.8 mm

A callout such as "Ra 1.6" is shorthand for this whole set, with the rest implied by the drawing standard. Roughness is the measurable part of surface finish. For what a roughness value reveals about wear, sealing, and process stability, see what surface roughness tells you about a part.

How Do You Read Surface Finish Symbols?

Every surface finish symbol starts from the same basic shape, a check-mark-style line drawn against the surface. Small additions change what the symbol demands about how the surface was produced.

Basic symbol

What it means

A surface texture requirement applies. The process is not specified.

When it is used

Any process may produce the surface

Basic symbol with a horizontal bar

What it means

Material removal by machining is required

When it is used

Surfaces that must be cut, ground, or otherwise machined

Basic symbol with a circle

What it means

Material removal is prohibited

When it is used

Surfaces left as cast, forged, or rolled

Requirements are written around the symbol. The parameter and limit value sit with the symbol, and optional entries for production method, lay, and machining allowance sit nearby. Their exact positions differ between ISO and ASME Y14.36 drawings, so read the standard named in the title block.

The standard itself matters. ISO 21920-1 replaced ISO 1302 and updated how surface texture requirements are indicated, while US drawings commonly follow ASME Y14.36. Older drawings keep the rules they were drawn under, so confirm which edition applies before interpreting an unfamiliar callout.

What Do Lay Symbols Mean?

Lay is the direction of the dominant surface pattern, and it matters because a surface can seal or wear differently along and across its tool marks. A lay symbol on the callout tells the maker which pattern to produce.

Lay direction

Parallel to the boundary line of the surface

Example

Depends on tool path

Lay direction

Perpendicular to the boundary line

Example

Depends on tool path

Lay direction

Crossed in two slanted directions

Example

Honed surfaces

Lay direction

Multidirectional

Example

Lapped surfaces

Lay direction

Approximately circular around the center

Example

Face-turned surfaces

Lay direction

Approximately radial from the center

Example

Depends on tool path

Lay direction

Particulate, non-directional, or protuberant

Example

Bead-blasted or EDM surfaces

Surface Finish Chart: Ra Values and N-Grades

ISO roughness grades N1 to N12 each stand for one standard Ra value. They appear on older metric drawings and in some CAD title blocks, and they are the quickest way to translate a grade into a number. The chart below shows each grade with its Ra in both unit systems and a common use.

N12

Ra (µm)

Ra (µin)

2,000

Common use

As-cast or flame-cut, non-functional surfaces

N11

Ra (µm)

Ra (µin)

1,000

Common use

Rough, non-critical surfaces

N10

Ra (µm)

12.5

Ra (µin)

500

Common use

Rough machining, non-critical

Ra (µm)

6.3

Ra (µin)

250

Common use

Coarse machining, non-mating

Ra (µm)

3.2

Ra (µin)

125

Common use

General machined surfaces

Ra (µm)

1.6

Ra (µin)

Common use

Fine machining, close-fitting parts

Ra (µm)

0.8

Ra (µin)

Common use

Sealing and bearing surfaces

Ra (µm)

0.4

Ra (µin)

Common use

Ground surfaces, precision fits

Ra (µm)

0.2

Ra (µin)

Common use

Fine-ground, honed, or lapped surfaces

Ra (µm)

0.1

Ra (µin)

Common use

Lapped, high-precision sliding surfaces

Ra (µm)

0.05

Ra (µin)

Common use

Polished or superfinished surfaces

Ra (µm)

0.025

Ra (µin)

Common use

Gauge-grade and optical-grade surfaces

The "common use" column reflects typical practice, not a standard. The function of the part decides the right grade. Many shops treat 3.2 µm (125 µin) as the default for general machined surfaces, and every step finer adds machining time, so specify only the finish the part needs.

How Do You Convert µm to µin, and What Does RMS Mean?

Multiply micrometers by 39.37 to get microinches. That puts 1.6 µm at 63 µin and 0.8 µm at about 31.5 µin, which drawings conventionally round to 32 µin. Going the other way, divide microinches by 39.37.

RMS on an older US drawing means root mean square roughness, now called Rq. On a sinusoidal profile Rq is about 1.11 times Ra, so a 32 µin RMS callout corresponds to roughly 29 µin Ra. In practice, many shops read RMS and Ra as interchangeable. If the tolerance is tight, confirm which parameter the designer intended, because modern instruments report Ra by default.

How Do You Choose the Right Surface Finish Specification?

Start from what the surface has to do, then pick the coarsest finish that does it. A finer finish is not automatically better, as it raises cost, and some sliding surfaces need small valleys to hold lubricant.

  • Non-functional or as-produced surfaces: use the "material removal prohibited" symbol, or a coarse general limit such as 3.2 µm (125 µin).
  • Mating and press-fit surfaces: specify a finer value and check the lay, since the contact pattern matters.
  • Sealing and bearing surfaces: these are often held to 0.8 µm (32 µin) or finer, and dynamic seals may also need a controlled lay.
  • Surfaces that will be coated: leave enough texture for adhesion without leaving peaks the coating cannot cover.

Ra alone can miss problems. A single deep scratch barely moves the average, which is why a passing Ra measurement may not tell the whole story. When a drawing needs more than one number, add a peak-to-valley parameter or move to an areal parameter, as covered in Ra vs. Sa.

What About Appearance and Process-Based Finishes?

Not every finish is specified by roughness. Gloss, color, and pattern are hard to capture in a single value, so cosmetic and coated finishes are usually specified by process, by a reference sample, or by a coating standard, with Ra as a secondary control.

As-machined

What it is

Tool marks left by cutting

How it is usually specified

Ra limit on the drawing

Ground, honed, lapped

What it is

Abrasive refinement of a machined surface

How it is usually specified

Ra value, often with lay

Bead blasted

What it is

Uniform matte, non-directional texture from blasting media

How it is usually specified

Media type and size, process settings, or a reference sample

Brushed or satin

What it is

Directional grain from an abrasive belt or brush

How it is usually specified

Grit and grain direction, or a reference sample

Polished

What it is

Smooth, reflective surface

How it is usually specified

Grit sequence or Ra; gloss if cosmetic

Anodized or plated

What it is

A coating applied over the base surface

How it is usually specified

Coating specification and thickness (for example, MIL-A-8625 for anodizing). Coating can change roughness.

How Do You Verify a Surface Finish Callout?

A callout is only as reliable as the check behind it. Good surface finish measurement uses the same parameter as the drawing, the same cutoff, and a trace direction that respects the lay. Under ISO 21920 practice, a surface expected to measure Ra 0.1 to 2 µm is normally evaluated with a 0.8 mm cutoff over five cutoff lengths (4 mm), and Ra 2 to 10 µm uses a 2.5 mm cutoff. Different settings can give two inspectors two different numbers on the same part.

The right tool depends on the callout and the part:

  • Visual and tactile comparison plates: a fast shop-floor check against known samples, not a measurement.
  • Handheld stylus testers: a quick Ra or Rz reading on the part.
  • Benchtop stylus: traditional method for quantifying Ra or Rz across a 2D line of the part's surface
  • Benchtop optical systems: measure Ra, Rz, or 3D roughness parameters like Sa. Ideal for parts that are soft, small, easy to scratch, or when you need to measure an entire surface rather than a singular 2D line.
  • KEYENCE offers non-contact options for this step: the VK-X4000 series 3D Optical Profiling Microscope and the VR-6000 series Wide-Area Optical Profiler. For help choosing between 2D and 3D approaches, see moving from 2D to 3D roughness measurement.

Frequently Asked Questions

They state the surface texture requirement for a surface. The basic symbol allows any process; a symbol with a horizontal bar requires material removal by machining, and a symbol with a circle prohibits material removal. Parameter, limit value, and lay are written alongside.

An N-grade is a label, such as N8, that stands for one fixed Ra value, in this case 3.2 µm (125 µin). Ra is the underlying measured parameter. Both describe roughness, so the grade is just a shorthand for the number.

There is no single standard, but 3.2 µm (125 µin) Ra is a common default for general machined surfaces. Sealing and bearing surfaces are often held to 0.8 µm (32 µin) or finer. Always follow the value on the drawing.

RMS is root mean square roughness, now called Rq. On a sinusoidal profile it is about 1.11 times Ra. Many older US drawings use "RMS" loosely, so confirm the intended parameter when the tolerance is tight.

Multiply µm by 39.37. For example, 1.6 µm is 63 µin, and 0.8 µm is 31.5 µin though often conventionally rounded to 32 µin.

It means material removal is prohibited. The surface must stay as produced, such as cast, forged, or rolled, and any texture requirement applies to that as-produced surface.

By measuring the same parameter as the drawing names, using the specified cutoff, and tracing in the right direction relative to the lay. Stylus instruments cover standard Ra checks, and optical systems add areal values such as Sa in addition to standard line roughness measurements.

  • Wide-Area Optical Profiler VR-6000 series

Wide-Area Optical Profiler

VR-6000 series

← All articles

What this article says

More in Industrial & Industry 4.0

All →
Failure Analysis for Medical and Pharma Components: Document Root Causes and Support Complaint Investigations
Keyence

Failure Analysis for Medical and Pharma Components: Document Root Causes and Support Complaint Investigations

Clamp-On vs Inline Flow Meter: The True Installation Cost
Keyence

Clamp-On vs Inline Flow Meter: The True Installation Cost

How to Bring Your Products to Market Faster
Keyence

How to Bring Your Products to Market Faster

Reducing Measurement Uncertainty in Surface Roughness Analysis
Keyence

Reducing Measurement Uncertainty in Surface Roughness Analysis

How AI Makes Programming the KEYENCE IV4 Series Simpler
Keyence

How AI Makes Programming the KEYENCE IV4 Series Simpler

The best way to monitor your Code Reader from your office
Keyence

The best way to monitor your Code Reader from your office

More from Keyence

Failure Analysis for Medical and Pharma Components: Document Root Causes and Support Complaint Investigations
Keyence

Failure Analysis for Medical and Pharma Components: Document Root Causes and Support Complaint Investigations

Clamp-On vs Inline Flow Meter: The True Installation Cost
Keyence

Clamp-On vs Inline Flow Meter: The True Installation Cost

How to Bring Your Products to Market Faster
Keyence

How to Bring Your Products to Market Faster

Reducing Measurement Uncertainty in Surface Roughness Analysis
Keyence

Reducing Measurement Uncertainty in Surface Roughness Analysis

How AI Makes Programming the KEYENCE IV4 Series Simpler
Keyence

How AI Makes Programming the KEYENCE IV4 Series Simpler

The best way to monitor your Code Reader from your office
Keyence

The best way to monitor your Code Reader from your office